The Basics of Plumbing Skills When Installing a Bathtub
The Basics of Plumbing Skills When Installing a Bathtub
Blog Article
They are making several great points on How to Install a Bathtub in general in this great article just below.
Mounting a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is also a reasonably difficult task. If the old bathtub is conveniently obtainable, the job can move immediately; if you need to open a wall surface to get rid of the old tub and position the new bathtub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will certainly need a helper to move out the old tub as well as set in the new one. Make certain you have actually qualified on your own for the work and are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you might need a specialist plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your washroom if you have already gotten a brand-new bathtub and don't require to alter the plan of your previous water supply pipes.
Your devices and also product checklist should make up the following:
Preparing for the Installation
To start with, the supporting framework provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last placement.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite bothersome because of the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly come from the pipes. When the supply pipelines have been eliminated, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleaned of any type of old securing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the tub up until the spirit level reviews level.
To install taps, fit all-time low of the outermost versatile faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply as well as check all joints as well as new pipework for leakages and also tighten them if required. Load the bathtub as well as additionally inspect the overflow electrical outlet as well as the normal outlet for leakages.
Finally, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub needs to wait until the bathtub has actually been used a minimum of once as this will resolve it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin making sure that the washing machines remain in location between the faucet and the sink. Secure the tap in position with the producer supplied backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The previous type needs to be attached to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, leading to difficulties with dampness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, and are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always fill the bathtub with water before securing, to permit the motion experienced when the tub remains in usage. The sealant can crack rather early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily offered on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent person who reads about Tools You Need to Install a New Bathtub , I think sharing that blog post was a good thing. Do you know somebody who is in the market for the subject? Why not share it. I love reading our article about How to Install a Bathtub.
Address leaks promptly. Report this page